Useful “IP” Commands – Network Interfaces configuration (Linux)


To totally unlock this section you need to Log-in


Login

In this post, we are going to review how we can assign Static IP Address, Static Route, Default Gateway etc. Assigning IP Address on demand using IP command. IFCONFIG command is deprecated and replaced by IP command in Linux. However, IFCONFIG command is still works and available for most of the Linux distributions.

How do we configure Static IP Address Internet Protocol (IPv4)

To configure static IP Address, you need to update or edit network configuration file to assign an Static IP Address to a system. You must be superuser with su (switch user) command from terminal or command prompt.

For RHEL/CentOS/Fedora

Open and edit network configuration file for (eth0 or eth1) using your favorite editor. For example, to assigning IP Address to eth0 interface as follows.

[root@tecmint ~]# vi /etc/sysconfig/network-scripts/ifcfg-eth0

DEVICE="eth0" BOOTPROTO=static ONBOOT=yes TYPE="Ethernet" IPADDR=192.168.50.2 NAME="System eth0" HWADDR=00:0C:29:28:FD:4C GATEWAY=192.168.50.1

For Ubuntu/Debian/Linux Mint

Assign Static IP Address to eth0 interface editing configuration file /etc/network/interfaces to make permanent changes as shown below.

auto eth0
iface eth0 inet static
address 192.168.50.2
netmask 255.255.255.0
gateway 192.168.50.1

Next, restart network services after entering all the details using the following command.

# /etc/init.d/networking restart
$ sudo /etc/init.d/networking restart

How to Assign a IP Address to Specific Interface

The following command used to assign IP Address to a specific interface (eth1) on the fly.

# ip addr add 192.168.50.5 dev eth1
$ sudo ip addr add 192.168.50.5 dev eth1

Note: Unfortunately all these settings will be lost after a system restart.

How to Check an IP Address

To get the depth information of your network interfaces like IP Address, MAC Address information, use the following command as shown below.

# ip addr show
$ sudo ip addr show

1: lo: <loopback ,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <broadcast ,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 00:0c:29:28:fd:4c brd ff:ff:ff:ff:ff:ff inet 192.168.50.2/24 brd 192.168.50.255 scope global eth0 inet6 fe80::20c:29ff:fe28:fd4c/64 scope link valid_lft forever preferred_lft forever 3: eth1: <broadcast ,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 00:0c:29:28:fd:56 brd ff:ff:ff:ff:ff:ff inet 192.168.50.5/24 scope global eth1 inet6 fe80::20c:29ff:fe28:fd56/64 scope link valid_lft forever preferred_lft forever

How to Remove an IP Address

The following command will remove an assigned IP address from the given interface (eth1).

# ip addr del 192.168.50.5/24 dev eth1
$ sudo ip addr del 192.168.50.5/24 dev eth1

How to Enable Network Interface

The “up” flag with interface name (eth1) enables a network interface. For example, the following command will activates the eth1 network interface.

# ip link set eth1 up
$ sudo ip link set eth1 up

How to Disable Network Interface

The “down” flag with interface name (eth1) disables a network interface. For example, the following command will De-activates the eth1 network interface.

# ip link set eth1 down
$ sudo ip link set eth1 down

How do I Check Route Table?

Type the following command to check the routing table information of system.

# ip route show
$ sudo ip route show

10.10.20.0/24 via 192.168.50.100 dev eth0 192.168.160.0/24 dev eth1 proto kernel scope link src 192.168.160.130 metric 1 192.168.50.0/24 dev eth0 proto kernel scope link src 192.168.50.2 169.254.0.0/16 dev eth0 scope link metric 1002 default via 192.168.50.1 dev eth0 proto static

How do I Add Static Route

Why you need to add Static routes or Manual routes, because that the traffic must not pass through the default gateway. We need to add Static routes to pass traffic from best way to reach the destination.

# ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0
$ sudo ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0

How to Remove Static Route

To remove assigned static route, simply type the following command.

# ip route del 10.10.20.0/24
$ sudo ip route del 10.10.20.0/24

How do I Add Persistence Static Routes

All the above route will be lost after a system restart. To add permanent Static route, edit file /etc/sysconfig/network-scripts/route-eth0 (We are storing static route for (eth0) and add the following lines and save and exist. By default route-eth0 file will not be there, need to be created.

For RHEL/CentOS/Fedora

# vi /etc/sysconfig/network-scripts/route-eth0
10.10.20.0/24 via 192.168.50.100 dev eth0

For Ubuntu/Debian/Linux Mint

Open the file /etc/network/interfaces and at the end add the persistence Static routes. IP Addresses may differ in your environment.

$ sudo vi /etc/network/interfaces
auto eth0
iface eth0 inet static
address 192.168.50.2
netmask 255.255.255.0
gateway 192.168.50.100
#########{Static Route}###########
up ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0

Next, restart network services after entering all the details using the following command.

# /etc/init.d/network restart
$ sudo /etc/init.d/network restart

How do I Add Default Gateway

Default gateway can be specified globally or for in interface-specific config file. Advantage of default gateway is If we have more than one NIC is present in the system. You can add default gateway on the fly as shown below command.

# ip route add default via 192.168.50.100
$ sudo ip route add default via 192.168.50.100